The GigaProbes® DVT30-1MM is a complete interconnect development kit for a TDR hand probing solution to perform full PCB interconnect analysis in both time and frequency modes when the waveforms are process with the Tektronix IConnect® SI Software. With Two probes, you can measure TDR 50/100 ohm impedance and TDT to extract return and insertion loss S-parameters. Accessories are included to attached the probe to the Tektronix Articulating arms for hand free probing, setting the probe tips pitch and much more.
Contents of the GigaProbes® DVT30-1MM interconnect develop kit:
Qty 2: 30 GHz TDR Probes (patent pending) Convertible to Single 50 ohm or Differential 100 ohm, with gold plated Conductive Diamond probe tips for repeatable high-bandwidth TDR measurements when probing at ANY angle
Qty 2: GPMMA Attaches probe to Tektronix PPM100, PPM203B Articulating arms or any standard micro-positioner
Qty 1: Stainless Steel 110mm Tweezers for Fine Pitch Probe Adjustments and used to attach ground lead to convert probe to 50 ohms
Qty 1: Desk-Top 5X Macro-Lens Inspection Station
Qty 1: Model 10 SMA Wrench (patent pending) with Quick Calibrator Holes to set probe pitch and planarize probes to 0.8 mm, 1.0 mm, or 1.27 mm
Qty 2: Hand Held Probe Sleeve Adapters with EZ-Hold Foam Cushions
Qty 4: Right Angle SMA Elbows for easy routing of TDR of SMA cables
Qty 1: 50 ohm conversion kit includes 2 SMA shorting caps, ground strap and shrink wrap.
Qty 4: Cable 24GHz SMA-SMA Cables
Qty 1: Resource CD with IConnect® application notes, data sheets
* Free Tektronix IConnect® Video Downloadable Training Course and Application Notes
DVT30-1MM-1 Impedacne and Failure Analysis Probing Kit
DVT30-1MM-1 Impedacne and Failure Analysis Kit for the Tektronix DSA8200 TDR Oscilloscope System
Close-up of the DVT30-1MM-1 Impedacne and Failure Analysis kit
The GigaProbes® DVT30-1MM-1 is a complete interconnect development kit for a TDR hand probing solution for PCB interconnect impedance analysis and Failure Analysis With One probe, you can measure TDR 50/100 ohm impedance and perform Failure Analysis on PCB's or Device Packages using the Tektronix IConnect® SI software. Accessories are included to attached the probe to the Tektronix Articulating arms for hand free probing, setting the probe tips pitch and much more.
Contents of the GigaProbes® DVT30-1MM-1 interconnect develop kit:
Qty 1: 30 GHz TDR Probes (patent pending) Convertible to Single 50 ohm or Differential 100 ohm, with gold plated Conductive Diamond probe tips for repeatable high-bandwidth TDR measurements when probing at ANY angle
Qty 2: GPMMA Attaches probe to Tektronix PPM100, PPM203B Articulating arms or any standard micro-positioner
Qty 1: Stainless Steel 110mm Tweezers for Fine Pitch Probe Adjustments and used to attach ground lead to convert probe to 50 ohms
Qty 1: Desk-Top 5X Macro-Lens Inspection Station
Qty 1: Model 10 SMA Wrench (patent pending) with Quick Calibrator Holes to set probe pitch and planarize probes to 0.8 mm, 1.0 mm, or 1.27 mm
Qty 1: Hand Held Probe Sleeve Adapters with EZ-Hold Foam Cushions
Qty 2: Right Angle SMA Elbows for easy routing of TDR of SMA cables
Qty 1: 50 ohm conversion kit includes 2 SMA shorting caps, ground strap and shrink wrap.
Qty 2: Cable 24GHz SMA-SMA Cables
Qty 1: SOLT kit (F Short, Open, Load Through)
Qty 1: Resource CD with IConnect® application notes, data sheets
* Free Tektronix IConnect® Video Downloadable Training Course and Application Notes
SOLT Kit Data Sheet
SLOT TDR Calibration Kit: 50ohm load, Short, Open, Through
